Rail Templating: Why a Handrail Is Made to Your Stair, Not a Drawing

Rail Templating: Why a Handrail Is Made to Your Stair, Not a Drawing

Rail templating starts where the tape measure stops, because a straight handrail on a straight flight can be built from a tape measure and a few numbers. The moment the rail turns a corner, climbs over a landing or follows a curve, numbers stop being enough. That is the job rail templating does.

What is rail templating?

Rail templating means taking a pattern of the handrail’s path directly from the stair on site, then shaping the rail in the shop to match it. It is used wherever the rail turns, curves or changes pitch, because those are the places where a small difference between the plan and the building shows up as a joint that will not close or a rail that sits higher over one flight than the next.

Why a drawing is not enough

Every staircase starts as a design, and a building can drift a little from its design. Framing can end up a few millimetres out of square. A landing can sit slightly higher than drawn. A curved wall can turn out to be a gentler curve than the plan says. On a straight run none of that matters much, because the rail simply follows the pitch of the flight.

Where the rail has to change direction, those small differences all arrive at the same place. The turn is where two flights, a landing and a newel meet, and a rail made from the drawing alone has to absorb every difference between the drawing and the stair in one joint.

Light wood handrail turning at a landing above black turned newels, with black balusters on both flights

In a turn like this one, with a light wood handrail over black turned newels and black balusters, the angle of the rail and its height on each side are set by the stair as built. Taking them off the stair is what lets the rail sit evenly over the nosings on both flights, instead of being forced to fit a plan.

How rail templating works

Stair in place

A template needs real treads, a real landing and real newel positions, so it is taken from a stair that is standing. On a renovation that is the existing stair; on a new build it is the stair once it is installed.

Pattern taken on site

The path of the rail is traced from the stair itself: the pitch of each flight, the height over the nosings, where the rail turns and where it ends at a newel or a wall.

Rail shaped in the shop

The handrail and its fittings are cut and joined to the pattern, so every turn is made for this stair and no other.

Wood handrails and black balusters on both sides of a flight rising to an upper landing railing

At the top of a flight like this one, the stair rail meets the railing around the landing. The height and angle where the two join are set by the stair as built, and that joint is exactly the kind of detail that is templated rather than calculated.

Where it matters most

Turns at a landing

The rail leaves one flight, crosses a landing and joins the next at a different height. Every one of those heights comes off the stair.

Curves

A curve gives no corner to hide a difference in radius. The whole length of the rail has to agree with the stair it follows.

Rails on glass

A handrail mounted on glass follows the glass, and the glass follows the stair. The rail has to meet the top of the flight exactly where the stair puts it.

Rails meeting walls

Where a rail ends at a wall or runs along one, the real wall decides the fit, and a real wall can be less flat or square than the drawing.

Rail templating on glass: light wood handrail on the face of a glass guard, turning at the landing

On a glass guard like this, the rail is fixed to the face of the glass and follows it down the flight and around the turn. How glass relates to the built stair is set out in why glass is measured last.

Straight runs are still measured

Rail templating does not replace measuring. The template is for the parts of a rail that change direction, and on a stair with no turns and no curves there may be nothing to template at all. Metal railings follow their own logic and are made in sections, as explained in why a metal railing arrives in pieces. The province publishes its building codes and standards online as a reference for handrails and guards.

Fit is what the eye reads first

The profile of a handrail is what your hand feels, and the options are set out in choosing a handrail profile. Fit is what your eye reads from across the room. A rail can be exactly the right profile and still look wrong if it sits high over one flight and low over the next, or kinks where it should flow. Templating is how the fit is settled before the rail ever reaches the house.

Questions about rail templating

Does every handrail need rail templating?

No. A straight rail on a straight flight can be built from measurements. Templating is for rails that turn, curve, climb over a landing or meet another rail at an angle, because those are the places where a small difference between the plan and the building shows up as a joint that will not close.

How are curved handrails made?

Curved handrails are made from thin strips of wood glued together, bent around a form and clamped until the glue sets. Ironwood has its own wood shop, so the form can follow the curve of the stair it is made for, and the finished rail keeps one smooth line from the bottom of the curve to the top.

How do I get a quote for a handrail with turns or curves?

Send Ironwood a few photos of the stair and a note on where the rail needs to go: around a landing, over a curve or along glass. Plans work for a new build. Ironwood works in Calgary and area; call (403) 552-1007 or use the contact page.

Planning a stair with turns or curves?

Send Ironwood a few photos of the stair and a note on where the rail needs to go.

Start Your Estimate

×
Press Enter to search. E.g., 'glass railings', 'mono stringer', 'calgary'