Rake or Level? Why Stair Glass Costs More Than Balcony Glass

Rake or Level? Why Stair Glass Costs More Than Balcony Glass

Stair glass and balcony glass can share a house, a thickness, the hardware and the finish on the posts, and still differ in cost. One costs noticeably more per square foot than the other. The only difference is that one of them is on an angle.

Why does glass on a staircase cost more than glass on a balcony?

Because a level panel is a rectangle and a raked panel is not. A panel running up a flight has to be cut as a parallelogram matched to the exact pitch of that specific staircase, and tempered glass cannot be trimmed, drilled or eased once it has been through the furnace. A level run can be made from standard rectangles, and a small cutting error can sometimes be absorbed. On a rake, the panel either fits that flight or it is scrap.

Stair glass railing with black metal frames following the rake of a light staircase in a white room

The panel in that photograph is not a square of glass turned on an angle. Its top and bottom edges run parallel to the pitch of the stair and its ends are cut vertical, which makes it a parallelogram with two angles that exist nowhere else in the building. The angle comes from the rise and run of that particular flight, which was itself decided by a floor-to-floor height that need not be a round number.

Stair glass and a level run are not the same job

A level run

  • Panels are rectangles, so a long run can be divided into equal repeating widths.
  • Standard stock sizes can work with little or no custom cutting.
  • A small measurement error can land in a gap or behind a clamp.
  • Panels are interchangeable: three identical panels can go in any order.
  • Templating is a straight line and a couple of heights.

A raked flight

  • Every panel is a parallelogram matched to one pitch.
  • Nothing is stock. Each panel is cut to that flight and no other.
  • An error of a few millimetres at the top edge is a new panel.
  • Panels are not interchangeable: each belongs in one position.
  • Templating has to capture pitch, plumb and the real position of every post.

Level run of dark tinted glass in a black metal frame along an upper floor edge with wood flooring

That is the easy condition. The run is level, the panels are rectangles, and the same panel could be lifted out and dropped back in three positions along the same edge. If a wall is a few millimetres out at one end, the difference is absorbed in the joint between panels and nobody ever sees it. Nothing about that is true once the same railing starts climbing.

Why the glass cannot simply be trimmed

Toughened glass gets its strength from a controlled heat and cooling cycle that leaves the surface in compression and the core in tension. That stress state is the whole point, and it is also why the panel becomes uncuttable. Score a tempered panel and it does not part along the line; it releases the stored stress and turns into a pile of small cubes. So the parallelogram has to be exactly right while the sheet is still ordinary glass, before it is toughened.

On a level run, a small error is a wider joint. On a rake, a small error is a new panel and a fresh wait.

This is also why a raked panel is not ordered from a drawing alone. The drawing tells us the pitch the stair was designed to. The building tells us the pitch the stair actually got, after the framing, the subfloor build-up and the finished floor thickness each moved by a few millimetres. Those numbers are taken from the installed staircase with the posts standing, which is the same reason glass is measured last.

Clear raked glass panels meeting a black square handrail on black brackets partway up a stair

Where a raked panel meets a handrail or a post, the joint is cut to the same angle as the panel. There is no adjustment left in it. That is the detail that has to be correct on the template, long before anyone sees the glass.

What this means for a quote

Measure the flights separately

A house with two flights of different pitch has two unrelated sets of panels. They are not a quantity of the same thing, and pricing them as one number hides a real cost.

Budget the rake higher per square foot

Expect the stair glass to carry a premium over the level runs in the same house. The material is the same; the cutting, handling and risk are not.

Expect raked panels to be measured last

Raked panels can only be templated once the posts are standing and plumb.

Build in remake time

If a raked panel is damaged in transit or on site, it is a fresh order, not a repair. Plan the schedule with that possibility in it rather than around it.

When a level run is quietly the better answer

Not every opening has to be raked. A landing, a mezzanine edge or a loft rail is level by nature, and a design that keeps the glass on the level portions and uses a metal or timber infill up the flight is not a compromise. It is a legitimate look, and it is cheaper and easier to replace. The decision worth making early is whether the glass up the flight is doing something for the room, or whether it is there because the level run was glass and the flight came along for the ride.

Questions about stair glass

Can a tempered stair glass panel be cut down to fit?

No. A tempered panel is finished at the size it was made and stays that size. This matters more on stair glass than on a level run, because a raked panel has two angles that belong to one flight and nothing else, so there is no other opening in the house where it could be reused either.

Why does the pitch of my stair not match the drawing?

Because the drawing is a design and the house is a construction. Subfloor thickness, floor finish and framing tolerance each move the rise by a few millimetres, and the pitch follows. That is normal, and it is why stair glass is templated from the built stair with the posts standing rather than ordered from the drawing.

Could laminated glass be cut on site instead?

Laminated glass made from ordinary glass can be cut, but a railing laminate made from tempered layers cannot, for the same reason a single tempered panel cannot. Either way, a finished railing panel is not something to trim on site, which is why the template for every raked panel has to be right before the glass is ordered.

The rake is also why the top rail question changes

On a level run, a capping rail is largely an aesthetic decision. On a flight it has a second job, because it ties a line of individually cut panels into one continuous element and gives the hand something to follow at a constant height above the nosings. The answer is not automatic in either direction, and we work through it in does a glass railing need a top rail. The rules for guards and handrails on stairs sit in the province’s published building codes and standards.

Working out where the glass should climb and where it should stay level

Send us photos of the flight and the level edges, with the floor-to-floor height, for a quote on the stair glass and the level runs.

Request an Estimate

×
Press Enter to search. E.g., 'glass railings', 'mono stringer', 'calgary'